Why Learning Plumbing Basics is Essential for Installing a Bathtub
Why Learning Plumbing Basics is Essential for Installing a Bathtub
Blog Article
This article in the next paragraphs on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is really informative. You should take a peek.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably challenging task. If the old tub is easily available, the job can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and also place the new tub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need an assistant to move out the old bathtub as well as set in the new one. Ensure you have certified on your own for the job as well as fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed job, it is far better to take into consideration using one before you start. Opportunities are you may require a specialist plumber to make tube links.
This write-up will aid you install a new bathtub in your bathroom if you have currently purchased a new bathtub as well as don't need to alter the arrangement of your previous water pipelines.
Your tools and material checklist must consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, activate the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the restricted access that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in position with the producer offered backnut. As soon as the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The previous kind ought to be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Tub
Using both wooden boards under its feet, place the bath tub in the called for placement. The wood boards are useful in evenly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub till the level checks out level.
To mount taps, fit the bottom of the furthest versatile faucet connector to the suitable supply pipe by making a compression join; then do the same for the various other tap.
Turn on the water system and also check all joints and also new pipework for leakages as well as tighten them if essential. Load the tub and additionally examine the overflow outlet and the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the bathtub needs to wait up until the bathtub has actually been utilized a minimum of when as this will certainly settle it right into its final placement.
Preparing for the Installation
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the area where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub remains in usage. The sealer can break rather early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our article on How to Install a Bathtub Yourself. Thanks a lot for spending some time to browse our short article. Sharing is good. Helping people is fun. Thank-you for going through it.
Plumber on standby. Call! Report this page